A Frequent Garage Door Issue That Arises From Multiple Causes.
If your garage door starts to lift and then suddenly comes back down, you are dealing with one of the issues garage door technicians get called about most often. It can seem like the door has a mind of its own, but there is almost always a real reason behind it. Modern garage doors are built with several safety features that stop the door whenever something seems off. A door that reverses on its own is simply one of those safety features doing exactly what it was designed to do. The encouraging part is that most of the reasons behind this behavior are simple to track down and repair. The frustrating part is that more than one thing can trigger the same symptom, so you have to rule them out one by one. The steps below follow the same checking order a trained garage door repair technician would use, which means you may be able to skip a service call if the answer turns out to be an easy one.
Begin by Inspecting the Photo Eye Sensors
The very first place to look is at the photo eye sensors. You will find them as two small dark boxes attached to the bottom of each side of the garage door opening, just a few inches off the ground. One box shoots an invisible beam across the doorway to the other box. Anytime something interrupts that beam while the door is closing or opening, the door automatically backs up so it doesn't squash whatever it has detected. Step over to the door and take a careful look at website both units. They need to be aimed straight at each other with no tilt. Almost every sensor has a tiny indicator light, usually green or red. A green light typically tells you everything is fine. A red light usually points to a blockage or an alignment issue. Inspect the lens for spider webs, dirt, fallen leaves, or any small object resting in front of it. Use a clean, soft cloth to wipe each lens. If the red light stays on after cleaning, carefully tap one sensor a little at a time until both lights show green. Fixing the photo eyes takes care of close to half of the cases where a garage door reverses on its own.
Inspect for Obstructions in the Garage Door Tracks.
If the sensors appear to be functioning properly, the next thing to inspect is the door’s tracks on each side—those metal rails that guide the rollers up and down. Frequently, a tiny object can become lodged in the track, such as a stone, a child’s toy, or a piece of cardboard from a shipped package. When the door lifts, it strikes the obstruction, and the opener interprets the resulting resistance as an unexpected obstacle, prompting the safety mechanism to reverse the door’s motion. Examine both tracks from top to bottom while the door is fully open and clear away any debris. While you’re at it, look for rollers that may be bent or broken, since damaged rollers can also generate resistance that the opener detects as a problem.
How to Properly Inspect Your Garage Door Springs
Above the door, you'll see one or two long metal springs. These are called torsion springs, and they do most of the work of lifting the door. The opener motor really just guides the door. The springs lift it. When a spring is worn out or broken, the door becomes very heavy, and the opener struggles to lift it. After a few feet of struggle, the opener gives up and reverses. To check the springs, look for any obvious gap or break in the coil. A broken spring usually has a clear two-inch gap where the metal snapped. If a spring is broken, do not try to fix it yourself. Torsion springs hold a huge amount of energy and can cause serious injury if handled wrong. This is a job for a trained technician. The repair usually runs between two hundred and four hundred dollars.
Test the Door's Balance by Hand
Even if the springs look okay, they might be weakening. Here's a simple test. Pull the red emergency release cord that hangs from the opener rail. This disconnects the door from the motor. Now lift the door by hand. A properly balanced door should feel light. You should be able to lift it with one hand, and it should stay in place when you let go halfway up. If the door feels very heavy, or if it slides back down when you let go, the springs are losing strength. A weak spring is one of the most common reasons a door reverses partway through the lift. Once you've tested, pull the release cord back toward the opener to reconnect it.
Adjust the Force Settings on the Opener
Every garage door opener has two small dials or buttons on the back of the motor housing. One controls the force used to open the door, and one controls the force used to close it. Over time, as parts wear and seasons change, the opener may need slightly more force to do its job. If the force setting is too low, the opener thinks any resistance means it has hit something, so it reverses. The owner's manual for your LiftMaster, Chamberlain, Genie, or Craftsman opener will show you exactly where these settings are. Adjust the open force dial slightly upward, then test the door. Adjust in small steps. Setting the force too high creates a safety risk because the opener will keep pushing even when it shouldn't.
Look at the Travel Limit Settings
The travel limits indicate opener the lower positions the door settings may cause the opener to the door has reached its limit and reverse. This issue commonly arises following a power outage, installation of a new opener, or maintenance work on the door. Similar, the controls for adjusting the travel limits are located of the opener motor a straightforward If the door is too high or not reaching the desired height, it with the travel limits and should be investigated if the door is not fully reversing.
Winter Mornings and Stiff Garage Doors
In winter, a stiff and cold garage door can put extra strain on the opener. Old grease in the tracks becomes thick, rollers don't spin as smoothly, and the door becomes harder to lift. The opener works harder, hits its force limit, and reverses. If your door only reverses on cold mornings and works fine the rest of the day, this is probably what's happening. The fix is to clean the tracks and lubricate the rollers, copyrights, and springs with a garage door specific lubricant. Avoid WD-40, which actually cleans grease off rather than adding it. Use a lithium or silicone spray made for garage doors.
When It's Time to Call a Garage Door Technician
If you've checked the sensors, the tracks, the springs, the force settings, the travel limits, and lubricated the door, and it still reverses, it's time to call a garage door repair contractor. At that point, the problem is usually inside the opener itself — a worn drive gear, a failing capacitor, or a damaged logic board. These repairs need proper tools and parts. A good technician can diagnose and fix most issues in under an hour, and the visit usually costs between one hundred and two hundred dollars before parts.